Service & Support for PMC-1002

New Transfer TurretSB 256.1 Bottom/Sidewall DKS Servo SystemsSB 253.1 Nexen Brake — New Brake SystemSB 254.2 Oil Cooling Fan Blades InstallationSB 250.1 Main Drive Motor Brake — Removing Tension SpringsSB 248.1 Seam Clamp Bolt — Replacing the Seam Clamp Bolt and NutSB 240.1 Bottom Forming Punch — New Shear DirectionSB 237.1 Seals: Bottom Maker Cutting & Draw RamsSB 228.1 Heater Element — ReplacementSB 222.1 Bottom Finish Assembly — Thread Locking CompoundSB 221.1 Sidewall Die Assembly — Bolts securing stripper plate to cutting punchSB 220.1 Bottom Finish/Lid Groove Station — New CamSB 235.1 Light Curtain — Replace Older Banner Style Light Curtain with the Newer Keyence Style Light CurtainSB 234.1 Main Drive Belt — Tensions ValuesSB 230.2 Transfer Turret — (New) Lower Transfer Turret Follower PlateSB 229.1 Gripper Module SpringsSB 227.1 Tamper Lubricator RetainerSB 224.1 Bottom Finish Assembly — Thread Locking CompoundSB 223.1 Roller Incurl Oil Applicator — Lube Assembly UpgradeSB 218.1 Transfer Turret — Upgrade KitSB 217.2 Single Piece Ramp Bottom Finish Roller AssemblySB 216.1 Motor BrakeSB 215.1 Bottom Finish Tooling — Thrust Bearing, Split Flange ToolingSB 214.2 Internal Wear — Turret FollowersSB 212.1 Main Oil Filter ElementSB 211.1 Slide Bottom Finish Station Retrofit PackageSB 209.2 Cup Diverter Regulator System Set-up Instructions — Leak Detector System UpgradeSB 208.1 Rotary Place, Vacuum Plate — Premature wearing on RulonSB 207.2 Mandrel Turret Seam Clamp Yoke Roller AssemblySB 205.1 Bottom Finish Station Cam Housing — Oil LevelSB 203.1 Bottom finish station cam housing — Vertical Shaft LocknutSB 202.1 Motor Brake LocknutSB 201.1 Main Drive Motor Brake Springs — Air Operated (Wichita) BrakesSB 200.1 Ultrasonic Sensor — Change NotificationSB 199.1 Drive Sprockets on Angle DrivesSB 197.1 Transfer Turret GrippersSB 195.1 Rimming Ejector Pin Change — Retaining RingSB 194.1 Mandrel Stem Extend Assembly — Annual Maintenance InspectionSB 193.1 Seam Clamp Pivot Pins — Attention Maintenance PersonnelSB 190.1 Seam Clamp Pin RetainerSB 189.1 Machine Alignment FixturesSB 187.1 Thrust Bearing, Split Flange Bottom Finish Tooling — To Extend the Service Life of Ramp Style Bottom Finish Station ToolingSB 185.4 Station SpringsSB 183.1 Roller Incurl Station Retrofit Kit — Additional Shaft SupportSB 182.2 Break-In PeriodSB 179.1 Mandrel Assembly ReplacementSB 177.1 Needle Bearing Style Tooling — GreaseSB 171.1 Gas Panel — RetrofitSB 170.1 Gas Fired MachinesSB 164.1 Sidewall Die Hoist — Access Cover PlateSB 149.1 Sidewall Servo Feeder Benefits — Compared to Mechanical Indexing System with EMP RegistrationSB 145.1 Tamper Lubricator UpdateSB 140.1 Paper SpecificationsSB 139.1 Indented Bill of MaterialSB 135.1 Ceramic RollersSB 134.1 Oil Product By BrandSB 131.1 Mobil Oil Product Code NumbersSB 128.1 Test or Alignment Fixtures for all PIVIC MachinesSB 095.1 Cam FollowerSB 082.1

Nexen Brake - New Brake System Removal & InstallationINST 119.1 Bottom Finish Slide AssemblyINST 105.1 Mandrel Turret Re-Alignment ProcedureINST 106.1 Replacing the Folding Wing Puck AssemblyINST 98.1 How to Replace the Rotary Head Suction Cup Timing BeltINST 96.1 Replacing Followers Without Removing Follower PlateINST 90.3 Transfer Turret Lower Assembly — UpgradeINST 226.1 Grinding The SpacerINST 101.1